Forum FAH-Addict
• Index
Bonjour les filles !
Comme annoncé hier , j'ai reçu la GTX Titan !
Après plusieurs petits problèmes a l'installation ( je suis reparti sur une installation toute fraiche ) , des mises a jour a faire et une v7.3.6 qui fonctionne correctement ( il était temps
) , j'ai enfin pu plier avec cette carte !
Pour rappel , les spec de Titan :
-Dénomination GPU : GK110
-Unités de calcul : 2688
-Horloge GPU (MHz) : 837
-Horloge GPU Boost (MHz) : 876
-Nombre de transistors (milliard): 7,1
-Puissance de calcul SP (GFlops) : 4500
-Puissance de calcul DP (GFlops) : 1300
-Taille mémoire DDR5 (Go): 6
-Interface mémoire (bits) : 384
-Fréquence mémoire (MHz) : 1500
-TDP (W) : 250
-Connecteurs d'alimentation : 6+8
1 - Désolé mais j'ai pas l'habitude de tester du matos de cette façon , alors pardonnez moi si c'est un peu l'anarchie
2 - Pour mesurer la consommation , je me base sur GPU-Z qui m'indique en pourcentage le TDP de la carte ( cela fausse certes quelques peu le résultat , mais je doute que la différence entre la valeur GPU-Z et la valeur réelle soit énorme ( une dizaine de Watts tout au plus je pense ),
3 - Le GPU Boost monte la carte a 1006 Mhz lors du pliage ( valeur GPU-Z ) . Je me suis fais une plage de vitesse du ventilo sous EVGA Precision de façons a ne pas faire trop chauffer la carte ( elle est en ce moment a 69° pour un ventilo a 68% )) , le Vcore n'est pas modifié !
4 - Je rentrerai pas dans le débat "Est-ce que cette carte vaux ses 950€
-Petit problème lors du premier pliage : En effet , j'avais branché une 650Ti sur la CM , mais cela me divisais par 2 le PPD de la Titan ( pourquoi je sais pas
) , elle reste donc l'unique CG a plier sur cette plateforme !
---- Passons aux tests ( qui seront mis a jour en fonction des WU ) :
- 8043 :
- PPD : env. 32000
- TPF : 1m44s
- TDP : 65% soit environ 160W
- PPD/W : 200
PS : Au niveau de l'efficacité énergétique , y'a quand même un sacré bon en avant par rapport a Fermi ( je tourne a environ 100 PPD/W sur la 580 )
Edité par Aquina Le 10/03/2013 à 13h22
Comme annoncé hier , j'ai reçu la GTX Titan !
Après plusieurs petits problèmes a l'installation ( je suis reparti sur une installation toute fraiche ) , des mises a jour a faire et une v7.3.6 qui fonctionne correctement ( il était temps

Pour rappel , les spec de Titan :
-Dénomination GPU : GK110
-Unités de calcul : 2688
-Horloge GPU (MHz) : 837
-Horloge GPU Boost (MHz) : 876
-Nombre de transistors (milliard): 7,1
-Puissance de calcul SP (GFlops) : 4500
-Puissance de calcul DP (GFlops) : 1300
-Taille mémoire DDR5 (Go): 6
-Interface mémoire (bits) : 384
-Fréquence mémoire (MHz) : 1500
-TDP (W) : 250
-Connecteurs d'alimentation : 6+8
1 - Désolé mais j'ai pas l'habitude de tester du matos de cette façon , alors pardonnez moi si c'est un peu l'anarchie

2 - Pour mesurer la consommation , je me base sur GPU-Z qui m'indique en pourcentage le TDP de la carte ( cela fausse certes quelques peu le résultat , mais je doute que la différence entre la valeur GPU-Z et la valeur réelle soit énorme ( une dizaine de Watts tout au plus je pense ),
3 - Le GPU Boost monte la carte a 1006 Mhz lors du pliage ( valeur GPU-Z ) . Je me suis fais une plage de vitesse du ventilo sous EVGA Precision de façons a ne pas faire trop chauffer la carte ( elle est en ce moment a 69° pour un ventilo a 68% )) , le Vcore n'est pas modifié !
4 - Je rentrerai pas dans le débat "Est-ce que cette carte vaux ses 950€

-Petit problème lors du premier pliage : En effet , j'avais branché une 650Ti sur la CM , mais cela me divisais par 2 le PPD de la Titan ( pourquoi je sais pas

---- Passons aux tests ( qui seront mis a jour en fonction des WU ) :
- 8043 :
- PPD : env. 32000
- TPF : 1m44s
- TDP : 65% soit environ 160W
- PPD/W : 200
PS : Au niveau de l'efficacité énergétique , y'a quand même un sacré bon en avant par rapport a Fermi ( je tourne a environ 100 PPD/W sur la 580 )
Edité par Aquina Le 10/03/2013 à 13h22
Le PPD me parait bien faible ... j'avais vu le double sur le forum officiel ici : http://foldingforum.org/viewtopic.php?f=38&t=23824
Tu as activé le mode beta pour espérer avoir des WUs et des cores mieux compatibles avec Kepler ?
Tu as activé le mode beta pour espérer avoir des WUs et des cores mieux compatibles avec Kepler ?
Oui c'est fait, mais avec la chance que j'ai , je doute que ça fonctionne 
J'ai remplacé la version actuelle du core GPU par la 2.22 , on verra ..........
EDIT: le client voulais plus se lancer , donc réinstallation !
J'ai du mal m'y prendre en rentrant les paramètres au premiers essais , maintenant je tourne avec le core 0x17
Mais ça plante au bout de 1 ou 2 minutes
Une copie du log si ça peut aider :
15:17:27:FS00:Set client configured
15:19:33:WU01:FS00:Connecting to assign-GPU.stanford.edu:80
15:19:34:WU01:FS00:News: Welcome to Folding@Home
15:19:34:WU01:FS00:Assigned to work server 171.67.108.149
15:19:34:WU01:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:19:34:WU01:FS00:Connecting to 171.67.108.149:8080
15:19:35:WU01:FS00:Downloading 1.39MiB
15:19:41:WU01:FS00:Download 27.02%
15:19:47:WU01:FS00:Download 63.06%
15:19:53:WU01:FS00:Download 99.09%
15:19:53:WU01:FS00:Download complete
15:19:53:WU01:FS00:Received Unit: id:01 state
OWNLOAD error:NO_ERROR project:7662 run:24 clone:22 gen:0 core:0x17 unit:0x00000001ff3d4835513921e55f99a564
15:19:53:WU01:FS00:Downloading core from http://www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah
15:19:53:WU01:FS00:Connecting to www.stanford.edu:80
15:19:54:WU01:FS00:FahCore 17: Downloading 2.11MiB
15:20:00:WU01:FS00:FahCore 17: 17.78%
15:20:06:WU01:FS00:FahCore 17: 35.56%
15:20:12:WU01:FS00:FahCore 17: 53.34%
15:20:18:WU01:FS00:FahCore 17: 71.12%
15:20:24:WU01:FS00:FahCore 17: 100.00%
15:20:24:WU01:FS00:FahCore 17: Download complete
15:20:24:WU01:FS00:Valid core signature
15:20:24:WU01:FS00:Unpacked 7.29MiB to cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe
15:20:24:WU01:FS00:Starting
15:20:24:WU01:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 01 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:20:24:WU01:FS00:Started FahCore on PID 4344
15:20:25:WU01:FS00:Core PID:4528
15:20:25:WU01:FS00:FahCore 0x17 started
15:20:25:WU01:FS00:0x17:*********************** Log Started 2013-03-10T15:20:25Z ***********************
15:20:25:WU01:FS00:0x17:Project: 7662 (Run 24, Clone 22, Gen 0)
15:20:25:WU01:FS00:0x17:Unit: 0x00000001ff3d4835513921e55f99a564
15:20:25:WU01:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:20:25:WU01:FS00:0x17:Machine: 0
15:20:25:WU01:FS00:0x17:Reading tar file system.xml
15:20:26:WU01:FS00:0x17:Reading tar file integrator.xml
15:20:26:WU01:FS00:0x17:Reading tar file state.xml
15:20:26:WU01:FS00:0x17:Reading tar file core.xml
15:20:26:WU01:FS00:0x17:Digital signatures verified
15:20:48:WU01:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:22:30:WARNING:WU01:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
15:22:30:WU01:FS00:Sending unit results: id:01 state:SEND error:FAULTY project:7662 run:24 clone:22 gen:0 core:0x17 unit:0x00000001ff3d4835513921e55f99a564
15:22:30:WU01:FS00:Uploading 2.45KiB to 171.67.108.149
15:22:30:WU01:FS00:Connecting to 171.67.108.149:8080
15:22:30:WU02:FS00:Connecting to assign-GPU.stanford.edu:80
15:22:31:WU02:FS00:News: Welcome to Folding@Home
15:22:31:WU02:FS00:Assigned to work server 171.67.108.149
15:22:31:WU02:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:22:31:WU02:FS00:Connecting to 171.67.108.149:8080
15:22:32:WU01:FS00:Upload complete
15:22:32:WU01:FS00:Server responded WORK_ACK (400)
15:22:32:WU01:FS00:Cleaning up
15:22:33:WU02:FS00:Downloading 1.62MiB
15:22:39:WU02:FS00:Download 46.27%
15:22:45:WU02:FS00:Download 88.68%
15:22:46:WU02:FS00:Download complete
15:22:46:WU02:FS00:Received Unit: id:02 state
OWNLOAD error:NO_ERROR project:7662 run:12 clone:8 gen:9 core:0x17 unit:0x0000000cff3d4835513919783cfdbc6e
15:22:46:WU02:FS00:Starting
15:22:46:WU02:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 02 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:22:46:WU02:FS00:Started FahCore on PID 4860
15:22:46:WU02:FS00:Core PID:3544
15:22:46:WU02:FS00:FahCore 0x17 started
15:22:47:WU02:FS00:0x17:*********************** Log Started 2013-03-10T15:22:46Z ***********************
15:22:47:WU02:FS00:0x17:Project: 7662 (Run 12, Clone 8, Gen 9)
15:22:47:WU02:FS00:0x17:Unit: 0x0000000cff3d4835513919783cfdbc6e
15:22:47:WU02:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:22:47:WU02:FS00:0x17:Machine: 0
15:22:47:WU02:FS00:0x17:Reading tar file state.xml
15:22:47:WU02:FS00:0x17:Reading tar file system.xml
15:22:47:WU02:FS00:0x17:Reading tar file integrator.xml
15:22:47:WU02:FS00:0x17:Reading tar file core.xml
15:22:47:WU02:FS00:0x17:Digital signatures verified
15:23:01:WU02:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:27:54:WU02:FS00:0x17:Completed 50000 out of 2500000 steps (2%)
15:32:00:WU02:FS00:0x17:ERROR:exception: Error downloading array posq: clEnqueueReadBuffer (-5)
15:32:00:WU02:FS00:0x17:Saving result file logfile_01.txt
15:32:00:WU02:FS00:0x17:Saving result file log.txt
15:32:00:WU02:FS00:0x17:Folding@home Core Shutdown: BAD_WORK_UNIT
15:32:00:WARNING:WU02:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
15:32:01:WU02:FS00:Sending unit results: id:02 state:SEND error:FAULTY project:7662 run:12 clone:8 gen:9 core:0x17 unit:0x0000000cff3d4835513919783cfdbc6e
15:32:01:WU02:FS00:Uploading 2.47KiB to 171.67.108.149
15:32:01:WU02:FS00:Connecting to 171.67.108.149:8080
15:32:01:WU01:FS00:Connecting to assign-GPU.stanford.edu:80
15:32:02:WU01:FS00:News: Welcome to Folding@Home
15:32:02:WU01:FS00:Assigned to work server 171.67.108.149
15:32:02:WU01:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:32:02:WU01:FS00:Connecting to 171.67.108.149:8080
15:32:02:WU02:FS00:Upload complete
15:32:02:WU02:FS00:Server responded WORK_ACK (400)
15:32:02:WU02:FS00:Cleaning up
15:32:03:WU01:FS00:Downloading 1.62MiB
15:32:09:WU01:FS00:Download 23.09%
15:32:15:WU01:FS00:Download 50.02%
15:32:21:WU01:FS00:Download 96.20%
15:32:21:WU01:FS00:Download complete
15:32:21:WU01:FS00:Received Unit: id:01 state
OWNLOAD error:NO_ERROR project:7662 run:2 clone:18 gen:7 core:0x17 unit:0x00000009ff3d4835513912b62c493765
15:32:21:WU01:FS00:Starting
15:32:21:WU01:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 01 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:32:21:WU01:FS00:Started FahCore on PID 3960
15:32:21:WU01:FS00:Core PID:4240
15:32:21:WU01:FS00:FahCore 0x17 started
15:32:22:WU01:FS00:0x17:*********************** Log Started 2013-03-10T15:32:22Z ***********************
15:32:22:WU01:FS00:0x17:Project: 7662 (Run 2, Clone 18, Gen 7)
15:32:22:WU01:FS00:0x17:Unit: 0x00000009ff3d4835513912b62c493765
15:32:22:WU01:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:32:22:WU01:FS00:0x17:Machine: 0
15:32:22:WU01:FS00:0x17:Reading tar file state.xml
15:32:22:WU01:FS00:0x17:Reading tar file system.xml
15:32:22:WU01:FS00:0x17:Reading tar file integrator.xml
15:32:22:WU01:FS00:0x17:Reading tar file core.xml
15:32:22:WU01:FS00:0x17:Digital signatures verified
15:32:39:WU01:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:33:03:WU01:FS00:0x17:ERROR:exception: Error downloading array posq: clEnqueueReadBuffer (-5)
15:33:03:WU01:FS00:0x17:Saving result file logfile_01.txt
15:33:03:WU01:FS00:0x17:Saving result file log.txt
15:33:03:WU01:FS00:0x17:Folding@home Core Shutdown: BAD_WORK_UNIT
15:33:04:WARNING:WU01:FS00:FahCore returned: FAILED_1 (0 = 0x0)
15:33:04:WU01:FS00:Sending unit results: id:01 state:SEND error:FAULTY project:7662 run:2 clone:18 gen:7 core:0x17 unit:0x00000009ff3d4835513912b62c493765
15:33:04:WU01:FS00:Uploading 2.46KiB to 171.67.108.149
15:33:04:WU01:FS00:Connecting to 171.67.108.149:8080
15:33:04:WU02:FS00:Connecting to assign-GPU.stanford.edu:80
15:33:05:WU02:FS00:News: Welcome to Folding@Home
15:33:05:WU02:FS00:Assigned to work server 171.67.108.149
15:33:05:WU02:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:33:05:WU02:FS00:Connecting to 171.67.108.149:8080
15:33:05:WU01:FS00:Upload complete
15:33:05:WU01:FS00:Server responded WORK_ACK (400)
15:33:05:WU01:FS00:Cleaning up
15:33:06:WU02:FS00:Downloading 1.62MiB
15:33:12:WU02:FS00:Download 38.54%
15:33:18:WU02:FS00:Download 84.80%
15:33:20:WU02:FS00:Download complete
15:33:20:WU02:FS00:Received Unit: id:02 state
OWNLOAD error:NO_ERROR project:7662 run:11 clone:6 gen:6 core:0x17 unit:0x0000000aff3d4835513918baf5584bf9
15:33:20:WU02:FS00:Starting
15:33:20:WU02:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 02 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:33:20:WU02:FS00:Started FahCore on PID 3472
15:33:20:WU02:FS00:Core PID:1176
15:33:20:WU02:FS00:FahCore 0x17 started
15:33:20:WU02:FS00:0x17:*********************** Log Started 2013-03-10T15:33:20Z ***********************
15:33:20:WU02:FS00:0x17:Project: 7662 (Run 11, Clone 6, Gen 6)
15:33:20:WU02:FS00:0x17:Unit: 0x0000000aff3d4835513918baf5584bf9
15:33:20:WU02:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:33:20:WU02:FS00:0x17:Machine: 0
15:33:20:WU02:FS00:0x17:Reading tar file state.xml
15:33:20:WU02:FS00:0x17:Reading tar file system.xml
15:33:20:WU02:FS00:0x17:Reading tar file integrator.xml
15:33:20:WU02:FS00:0x17:Reading tar file core.xml
15:33:20:WU02:FS00:0x17:Digital signatures verified
15:33:32:WU02:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:34:53:WU02:FS00:0x17:ERROR:exception: Error downloading array posq: clEnqueueReadBuffer (-5)
15:34:53:WU02:FS00:0x17:Saving result file logfile_01.txt
15:34:53:WU02:FS00:0x17:Saving result file log.txt
15:34:53:WU02:FS00:0x17:Folding@home Core Shutdown: BAD_WORK_UNIT
15:34:53:WARNING:WU02:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
15:34:53:WU02:FS00:Sending unit results: id:02 state:SEND error:FAULTY project:7662 run:11 clone:6 gen:6 core:0x17 unit:0x0000000aff3d4835513918baf5584bf9
15:34:53:WU02:FS00:Uploading 2.46KiB to 171.67.108.149
15:34:53:WU02:FS00:Connecting to 171.67.108.149:8080
15:34:54:WU01:FS00:Connecting to assign-GPU.stanford.edu:80
15:34:54:WU01:FS00:News: Welcome to Folding@Home
15:34:54:WU01:FS00:Assigned to work server 171.67.108.149
15:34:54:WU01:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:34:54:WU01:FS00:Connecting to 171.67.108.149:8080
15:34:55:WU02:FS00:Upload complete
15:34:55:WU02:FS00:Server responded WORK_ACK (400)
15:34:55:WU02:FS00:Cleaning up
15:34:56:WU01:FS00:Downloading 1.62MiB
15:35:02:WU01:FS00:Download 42.35%
15:35:08:WU01:FS00:Download 88.54%
15:35:09:WU01:FS00:Download complete
15:35:09:WU01:FS00:Received Unit: id:01 state
OWNLOAD error:NO_ERROR project:7662 run:13 clone:19 gen:6 core:0x17 unit:0x00000007ff3d483551391a4b0115c3ee
15:35:09:WU01:FS00:Starting
15:35:09:WU01:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 01 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:35:09:WU01:FS00:Started FahCore on PID 3944
15:35:09:WU01:FS00:Core PID:4872
15:35:09:WU01:FS00:FahCore 0x17 started
15:35:10:WU01:FS00:0x17:*********************** Log Started 2013-03-10T15:35:09Z ***********************
15:35:10:WU01:FS00:0x17:Project: 7662 (Run 13, Clone 19, Gen 6)
15:35:10:WU01:FS00:0x17:Unit: 0x00000007ff3d483551391a4b0115c3ee
15:35:10:WU01:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:35:10:WU01:FS00:0x17:Machine: 0
15:35:10:WU01:FS00:0x17:Reading tar file state.xml
15:35:10:WU01:FS00:0x17:Reading tar file system.xml
15:35:10:WU01:FS00:0x17:Reading tar file integrator.xml
15:35:10:WU01:FS00:0x17:Reading tar file core.xml
15:35:10:WU01:FS00:0x17:Digital signatures verified
15:35:27:WU01:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:36:04:WU01:FS00:0x17:ERROR:exception: Error downloading array posq: clEnqueueReadBuffer (-5)
15:36:04:WU01:FS00:0x17:Saving result file logfile_01.txt
15:36:04:WU01:FS00:0x17:Saving result file log.txt
15:36:04:WU01:FS00:0x17:Folding@home Core Shutdown: BAD_WORK_UNIT
15:36:04:WARNING:WU01:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
15:36:04:WU01:FS00:Sending unit results: id:01 state:SEND error:FAULTY project:7662 run:13 clone:19 gen:6 core:0x17 unit:0x00000007ff3d483551391a4b0115c3ee
15:36:04:WU01:FS00:Uploading 2.46KiB to 171.67.108.149
15:36:04:WU01:FS00:Connecting to 171.67.108.149:8080
15:36:06:WU01:FS00:Upload complete
15:36:06:WU01:FS00:Server responded WORK_ACK (400)
15:36:06:WU01:FS00:Cleaning up
Ca répéte ça tout le temps , le pilote d'affichage plante et maintenant j'ai un gros FAILED qui s'affiche !
Edité par Aquina Le 10/03/2013 à 16h42

J'ai remplacé la version actuelle du core GPU par la 2.22 , on verra ..........
EDIT: le client voulais plus se lancer , donc réinstallation !
J'ai du mal m'y prendre en rentrant les paramètres au premiers essais , maintenant je tourne avec le core 0x17

Mais ça plante au bout de 1 ou 2 minutes

Une copie du log si ça peut aider :
15:17:27:FS00:Set client configured
15:19:33:WU01:FS00:Connecting to assign-GPU.stanford.edu:80
15:19:34:WU01:FS00:News: Welcome to Folding@Home
15:19:34:WU01:FS00:Assigned to work server 171.67.108.149
15:19:34:WU01:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:19:34:WU01:FS00:Connecting to 171.67.108.149:8080
15:19:35:WU01:FS00:Downloading 1.39MiB
15:19:41:WU01:FS00:Download 27.02%
15:19:47:WU01:FS00:Download 63.06%
15:19:53:WU01:FS00:Download 99.09%
15:19:53:WU01:FS00:Download complete
15:19:53:WU01:FS00:Received Unit: id:01 state

15:19:53:WU01:FS00:Downloading core from http://www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah
15:19:53:WU01:FS00:Connecting to www.stanford.edu:80
15:19:54:WU01:FS00:FahCore 17: Downloading 2.11MiB
15:20:00:WU01:FS00:FahCore 17: 17.78%
15:20:06:WU01:FS00:FahCore 17: 35.56%
15:20:12:WU01:FS00:FahCore 17: 53.34%
15:20:18:WU01:FS00:FahCore 17: 71.12%
15:20:24:WU01:FS00:FahCore 17: 100.00%
15:20:24:WU01:FS00:FahCore 17: Download complete
15:20:24:WU01:FS00:Valid core signature
15:20:24:WU01:FS00:Unpacked 7.29MiB to cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe
15:20:24:WU01:FS00:Starting
15:20:24:WU01:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 01 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:20:24:WU01:FS00:Started FahCore on PID 4344
15:20:25:WU01:FS00:Core PID:4528
15:20:25:WU01:FS00:FahCore 0x17 started
15:20:25:WU01:FS00:0x17:*********************** Log Started 2013-03-10T15:20:25Z ***********************
15:20:25:WU01:FS00:0x17:Project: 7662 (Run 24, Clone 22, Gen 0)
15:20:25:WU01:FS00:0x17:Unit: 0x00000001ff3d4835513921e55f99a564
15:20:25:WU01:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:20:25:WU01:FS00:0x17:Machine: 0
15:20:25:WU01:FS00:0x17:Reading tar file system.xml
15:20:26:WU01:FS00:0x17:Reading tar file integrator.xml
15:20:26:WU01:FS00:0x17:Reading tar file state.xml
15:20:26:WU01:FS00:0x17:Reading tar file core.xml
15:20:26:WU01:FS00:0x17:Digital signatures verified
15:20:48:WU01:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:22:30:WARNING:WU01:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
15:22:30:WU01:FS00:Sending unit results: id:01 state:SEND error:FAULTY project:7662 run:24 clone:22 gen:0 core:0x17 unit:0x00000001ff3d4835513921e55f99a564
15:22:30:WU01:FS00:Uploading 2.45KiB to 171.67.108.149
15:22:30:WU01:FS00:Connecting to 171.67.108.149:8080
15:22:30:WU02:FS00:Connecting to assign-GPU.stanford.edu:80
15:22:31:WU02:FS00:News: Welcome to Folding@Home
15:22:31:WU02:FS00:Assigned to work server 171.67.108.149
15:22:31:WU02:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:22:31:WU02:FS00:Connecting to 171.67.108.149:8080
15:22:32:WU01:FS00:Upload complete
15:22:32:WU01:FS00:Server responded WORK_ACK (400)
15:22:32:WU01:FS00:Cleaning up
15:22:33:WU02:FS00:Downloading 1.62MiB
15:22:39:WU02:FS00:Download 46.27%
15:22:45:WU02:FS00:Download 88.68%
15:22:46:WU02:FS00:Download complete
15:22:46:WU02:FS00:Received Unit: id:02 state

15:22:46:WU02:FS00:Starting
15:22:46:WU02:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 02 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:22:46:WU02:FS00:Started FahCore on PID 4860
15:22:46:WU02:FS00:Core PID:3544
15:22:46:WU02:FS00:FahCore 0x17 started
15:22:47:WU02:FS00:0x17:*********************** Log Started 2013-03-10T15:22:46Z ***********************
15:22:47:WU02:FS00:0x17:Project: 7662 (Run 12, Clone 8, Gen 9)
15:22:47:WU02:FS00:0x17:Unit: 0x0000000cff3d4835513919783cfdbc6e
15:22:47:WU02:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:22:47:WU02:FS00:0x17:Machine: 0
15:22:47:WU02:FS00:0x17:Reading tar file state.xml
15:22:47:WU02:FS00:0x17:Reading tar file system.xml
15:22:47:WU02:FS00:0x17:Reading tar file integrator.xml
15:22:47:WU02:FS00:0x17:Reading tar file core.xml
15:22:47:WU02:FS00:0x17:Digital signatures verified
15:23:01:WU02:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:27:54:WU02:FS00:0x17:Completed 50000 out of 2500000 steps (2%)
15:32:00:WU02:FS00:0x17:ERROR:exception: Error downloading array posq: clEnqueueReadBuffer (-5)
15:32:00:WU02:FS00:0x17:Saving result file logfile_01.txt
15:32:00:WU02:FS00:0x17:Saving result file log.txt
15:32:00:WU02:FS00:0x17:Folding@home Core Shutdown: BAD_WORK_UNIT
15:32:00:WARNING:WU02:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
15:32:01:WU02:FS00:Sending unit results: id:02 state:SEND error:FAULTY project:7662 run:12 clone:8 gen:9 core:0x17 unit:0x0000000cff3d4835513919783cfdbc6e
15:32:01:WU02:FS00:Uploading 2.47KiB to 171.67.108.149
15:32:01:WU02:FS00:Connecting to 171.67.108.149:8080
15:32:01:WU01:FS00:Connecting to assign-GPU.stanford.edu:80
15:32:02:WU01:FS00:News: Welcome to Folding@Home
15:32:02:WU01:FS00:Assigned to work server 171.67.108.149
15:32:02:WU01:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:32:02:WU01:FS00:Connecting to 171.67.108.149:8080
15:32:02:WU02:FS00:Upload complete
15:32:02:WU02:FS00:Server responded WORK_ACK (400)
15:32:02:WU02:FS00:Cleaning up
15:32:03:WU01:FS00:Downloading 1.62MiB
15:32:09:WU01:FS00:Download 23.09%
15:32:15:WU01:FS00:Download 50.02%
15:32:21:WU01:FS00:Download 96.20%
15:32:21:WU01:FS00:Download complete
15:32:21:WU01:FS00:Received Unit: id:01 state

15:32:21:WU01:FS00:Starting
15:32:21:WU01:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 01 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:32:21:WU01:FS00:Started FahCore on PID 3960
15:32:21:WU01:FS00:Core PID:4240
15:32:21:WU01:FS00:FahCore 0x17 started
15:32:22:WU01:FS00:0x17:*********************** Log Started 2013-03-10T15:32:22Z ***********************
15:32:22:WU01:FS00:0x17:Project: 7662 (Run 2, Clone 18, Gen 7)
15:32:22:WU01:FS00:0x17:Unit: 0x00000009ff3d4835513912b62c493765
15:32:22:WU01:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:32:22:WU01:FS00:0x17:Machine: 0
15:32:22:WU01:FS00:0x17:Reading tar file state.xml
15:32:22:WU01:FS00:0x17:Reading tar file system.xml
15:32:22:WU01:FS00:0x17:Reading tar file integrator.xml
15:32:22:WU01:FS00:0x17:Reading tar file core.xml
15:32:22:WU01:FS00:0x17:Digital signatures verified
15:32:39:WU01:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:33:03:WU01:FS00:0x17:ERROR:exception: Error downloading array posq: clEnqueueReadBuffer (-5)
15:33:03:WU01:FS00:0x17:Saving result file logfile_01.txt
15:33:03:WU01:FS00:0x17:Saving result file log.txt
15:33:03:WU01:FS00:0x17:Folding@home Core Shutdown: BAD_WORK_UNIT
15:33:04:WARNING:WU01:FS00:FahCore returned: FAILED_1 (0 = 0x0)
15:33:04:WU01:FS00:Sending unit results: id:01 state:SEND error:FAULTY project:7662 run:2 clone:18 gen:7 core:0x17 unit:0x00000009ff3d4835513912b62c493765
15:33:04:WU01:FS00:Uploading 2.46KiB to 171.67.108.149
15:33:04:WU01:FS00:Connecting to 171.67.108.149:8080
15:33:04:WU02:FS00:Connecting to assign-GPU.stanford.edu:80
15:33:05:WU02:FS00:News: Welcome to Folding@Home
15:33:05:WU02:FS00:Assigned to work server 171.67.108.149
15:33:05:WU02:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:33:05:WU02:FS00:Connecting to 171.67.108.149:8080
15:33:05:WU01:FS00:Upload complete
15:33:05:WU01:FS00:Server responded WORK_ACK (400)
15:33:05:WU01:FS00:Cleaning up
15:33:06:WU02:FS00:Downloading 1.62MiB
15:33:12:WU02:FS00:Download 38.54%
15:33:18:WU02:FS00:Download 84.80%
15:33:20:WU02:FS00:Download complete
15:33:20:WU02:FS00:Received Unit: id:02 state

15:33:20:WU02:FS00:Starting
15:33:20:WU02:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 02 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:33:20:WU02:FS00:Started FahCore on PID 3472
15:33:20:WU02:FS00:Core PID:1176
15:33:20:WU02:FS00:FahCore 0x17 started
15:33:20:WU02:FS00:0x17:*********************** Log Started 2013-03-10T15:33:20Z ***********************
15:33:20:WU02:FS00:0x17:Project: 7662 (Run 11, Clone 6, Gen 6)
15:33:20:WU02:FS00:0x17:Unit: 0x0000000aff3d4835513918baf5584bf9
15:33:20:WU02:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:33:20:WU02:FS00:0x17:Machine: 0
15:33:20:WU02:FS00:0x17:Reading tar file state.xml
15:33:20:WU02:FS00:0x17:Reading tar file system.xml
15:33:20:WU02:FS00:0x17:Reading tar file integrator.xml
15:33:20:WU02:FS00:0x17:Reading tar file core.xml
15:33:20:WU02:FS00:0x17:Digital signatures verified
15:33:32:WU02:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:34:53:WU02:FS00:0x17:ERROR:exception: Error downloading array posq: clEnqueueReadBuffer (-5)
15:34:53:WU02:FS00:0x17:Saving result file logfile_01.txt
15:34:53:WU02:FS00:0x17:Saving result file log.txt
15:34:53:WU02:FS00:0x17:Folding@home Core Shutdown: BAD_WORK_UNIT
15:34:53:WARNING:WU02:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
15:34:53:WU02:FS00:Sending unit results: id:02 state:SEND error:FAULTY project:7662 run:11 clone:6 gen:6 core:0x17 unit:0x0000000aff3d4835513918baf5584bf9
15:34:53:WU02:FS00:Uploading 2.46KiB to 171.67.108.149
15:34:53:WU02:FS00:Connecting to 171.67.108.149:8080
15:34:54:WU01:FS00:Connecting to assign-GPU.stanford.edu:80
15:34:54:WU01:FS00:News: Welcome to Folding@Home
15:34:54:WU01:FS00:Assigned to work server 171.67.108.149
15:34:54:WU01:FS00:Requesting new work unit for slot 00: READY gpu:0:GK110 [GeForce GTX Titan] from 171.67.108.149
15:34:54:WU01:FS00:Connecting to 171.67.108.149:8080
15:34:55:WU02:FS00:Upload complete
15:34:55:WU02:FS00:Server responded WORK_ACK (400)
15:34:55:WU02:FS00:Cleaning up
15:34:56:WU01:FS00:Downloading 1.62MiB
15:35:02:WU01:FS00:Download 42.35%
15:35:08:WU01:FS00:Download 88.54%
15:35:09:WU01:FS00:Download complete
15:35:09:WU01:FS00:Received Unit: id:01 state

15:35:09:WU01:FS00:Starting
15:35:09:WU01:FS00:Running FahCore: "C:\Program Files (x86)\FAHClient/FAHCoreWrapper.exe" C:/Users/Aquina/AppData/Roaming/FAHClient/cores/www.stanford.edu/~pande/Win32/AMD64/NVIDIA/Fermi/beta/Core_17.fah/FahCore_17.exe -dir 01 -suffix 01 -version 703 -lifeline 2508 -checkpoint 15 -gpu 0 -gpu-vendor nvidia
15:35:09:WU01:FS00:Started FahCore on PID 3944
15:35:09:WU01:FS00:Core PID:4872
15:35:09:WU01:FS00:FahCore 0x17 started
15:35:10:WU01:FS00:0x17:*********************** Log Started 2013-03-10T15:35:09Z ***********************
15:35:10:WU01:FS00:0x17:Project: 7662 (Run 13, Clone 19, Gen 6)
15:35:10:WU01:FS00:0x17:Unit: 0x00000007ff3d483551391a4b0115c3ee
15:35:10:WU01:FS00:0x17:CPU: 0x00000000000000000000000000000000
15:35:10:WU01:FS00:0x17:Machine: 0
15:35:10:WU01:FS00:0x17:Reading tar file state.xml
15:35:10:WU01:FS00:0x17:Reading tar file system.xml
15:35:10:WU01:FS00:0x17:Reading tar file integrator.xml
15:35:10:WU01:FS00:0x17:Reading tar file core.xml
15:35:10:WU01:FS00:0x17:Digital signatures verified
15:35:27:WU01:FS00:0x17:Completed 0 out of 2500000 steps (0%)
15:36:04:WU01:FS00:0x17:ERROR:exception: Error downloading array posq: clEnqueueReadBuffer (-5)
15:36:04:WU01:FS00:0x17:Saving result file logfile_01.txt
15:36:04:WU01:FS00:0x17:Saving result file log.txt
15:36:04:WU01:FS00:0x17:Folding@home Core Shutdown: BAD_WORK_UNIT
15:36:04:WARNING:WU01:FS00:FahCore returned: BAD_WORK_UNIT (114 = 0x72)
15:36:04:WU01:FS00:Sending unit results: id:01 state:SEND error:FAULTY project:7662 run:13 clone:19 gen:6 core:0x17 unit:0x00000007ff3d483551391a4b0115c3ee
15:36:04:WU01:FS00:Uploading 2.46KiB to 171.67.108.149
15:36:04:WU01:FS00:Connecting to 171.67.108.149:8080
15:36:06:WU01:FS00:Upload complete
15:36:06:WU01:FS00:Server responded WORK_ACK (400)
15:36:06:WU01:FS00:Cleaning up
Ca répéte ça tout le temps , le pilote d'affichage plante et maintenant j'ai un gros FAILED qui s'affiche !
Edité par Aquina Le 10/03/2013 à 16h42
Ah oui merde, pas de beta alors à cause du core 17 ... il n'est pas encore compatible avec Titan, il faut une maj des drivers

C'est intéressant ce topic
Tu as un wattmètre qui se branche a la prise ? C'est une méthode de mesure plutôt cohérente pour le plieur puisque ça mesure directement ce que facture EDF.

La GeForce Titan à un mode d'activation de la double précision,

http://www.tomshardware.fr/articles/GeForce-GTX-Titan-GK110,2-34-3.html
Est-ce que cela change quelque chose ?

http://www.tomshardware.fr/articles/GeForce-GTX-Titan-GK110,2-34-3.html
Est-ce que cela change quelque chose ?

Normalement, si rien n'a changé dans les cores, Folding@Home est toujours sur de la précision simple.
C'est bien ca ... donc pour plier, ca ne sert à rien.
Mais pour certains projets BOINC qui utilisent la double précision, ca peut servir.
Attention, activer cette option désactive le GPU Boost ...
Mais pour certains projets BOINC qui utilisent la double précision, ca peut servir.
Attention, activer cette option désactive le GPU Boost ...
Coucou les filles !
@toTOW : pas plus de beta avec la Titant qu'avec la GTX 580 , peut être un probléme lié au fait que le driver est une BETA aussi (314.09)
@Ada: j'ai un wattmétre oui , mais j'ai pas plus regardé que ça ! Vite fait , GPU-Z n'indique pas la bonne valeur , je tourne plutôt autour de 200W en réel !
@toTOW : pas plus de beta avec la Titant qu'avec la GTX 580 , peut être un probléme lié au fait que le driver est une BETA aussi (314.09)
@Ada: j'ai un wattmétre oui , mais j'ai pas plus regardé que ça ! Vite fait , GPU-Z n'indique pas la bonne valeur , je tourne plutôt autour de 200W en réel !
Les WU sont attribués au hasard.
Bien que le client v7 a introduit une option permettant de choisir parmi 4 catégories je crois de maladie/domaine de recherche.
Tu peux faire plier autant de CG qu'il y a de port PCI-E. Après ce qui limite c'est la largeur de la CG.
Edité par foo_fight Le 24/03/2013 à 23h11
Bien que le client v7 a introduit une option permettant de choisir parmi 4 catégories je crois de maladie/domaine de recherche.
Tu peux faire plier autant de CG qu'il y a de port PCI-E. Après ce qui limite c'est la largeur de la CG.
Edité par foo_fight Le 24/03/2013 à 23h11
Et l'alim ...
Coucou les gens
Petite capture d'écran , dommage que la carte soit pas stable a ces fréquences
( je cherche les fréquences stable en ce moment )
http://zupimages.net/viewer.php?id=2/994374811.jpg
EDIT : J'ai réussi a plier presque 3% sans plantage , en réduisant les fréquences ( ca plie toujours
) , PPD stabilisé a 68K environ !
Par contre j'ai mis 3 ventilos (
) en renfort pour la refroidir ( 1 au dos de la carte et 2 qui poussent de l'air vers la turbine ) , ben mine de rien j'ai grappillé entre 8 et 10° !
Edité par Aquina Le 30/03/2013 à 16h47

Petite capture d'écran , dommage que la carte soit pas stable a ces fréquences

( je cherche les fréquences stable en ce moment )
http://zupimages.net/viewer.php?id=2/994374811.jpg
EDIT : J'ai réussi a plier presque 3% sans plantage , en réduisant les fréquences ( ca plie toujours

Par contre j'ai mis 3 ventilos (

Edité par Aquina Le 30/03/2013 à 16h47
1136 MHz c'est excellent pour une Titan.

• Index
1 Utilisateur en ligne : 0 Administrateur, 0 Modérateur, 0 Membre et 1 Visiteur
Utilisateur en ligne : Aucun membre connecté
Utilisateur en ligne : Aucun membre connecté
Répondre
Vous n'êtes pas autorisé à écrire dans cette catégorie